Monday, November 9, 2020

These aren't the droids you're looking for...


The term "droid" is a registered trademark of Lucasfilm Ltd, and is the Star Wars universe equivalent of the word "robot". Star Wars droids come in a wide variety of forms, but most if not all, seem to be installed with some degree of artificial intelligence and personality.

I personally use the term loosely to refer to all cute, quirky, or comic relief robots from popular media. The majority of the various miniature versions of such robots that I've collected are droids from the Star Wars line of MicroMachines made by Galoob.

The first group of figures include four R-series astromech droids – one standalone, and three others on a single base. The fourth droid on the group base is a mining droid, followed by a gonk power droid (a couple of 1/72 resin kit from RetrokiT and Green Strawberry Models are available, but I don't know how they compare in size to the MicroMachines version). The last two figures are a LE-series repair droid and a ASP-series general-purpose labor droid.

R2-D2, R1-G4, R2-D2, R5-D4, LIN-V8K, GNK, LE-BO2D9, ASP-7

The next image has three 3PO humanoid protocol droids and an assassin droid. The 3PO droids are tiny, and seem to be 1/87 scale. I think the E-3PO droid is a custom repaint or factory error of C-3PO since I don't think that there was an actual MicroMachines version of E-3PO.

C-3PO, C-3PO (god mode), E-3PO, IG-88

The droids that I like the most from the MicroMachines line are the B1 battle droids.


The duplicate poses are from the various playsets, and are distinguished from the standard figures by having a small hole through the middle of the base.


The battle droids are most likely 1/76 scale, so may appear somewhat under height, but overall, they still look fine with 1/72 figures.


Larger scale battle droids were made for the Star Wars Action Fleet line, but they don't have the spindly look of the droids from the films. I think that the S.T.A.P. (Single Trooper Aerial Platform) looks okay with the smaller figure riding it, so I'm fine with calling it 1/72 scale.


I have two other Action Fleet droids from the Pod Racer Hangar Bay set. Both are DUM-series pit droids. The tan colored droid has the pivoting hips of the typical Action Fleet figure, while the brown droid is a fixed pose figure.


At 21mm in height, they are about 1 scale foot taller than they should be, but I'm willing to let that pass.

In metal, Ground Zero Games makes a WorkBot pack (SG15-V13), with three small robots who are expys of R2D2, WALL•E (Waste Allocation Load Lifter Earth-Class), and Dewey (or Louie) from Silent Running.

I misplaced the other miniatures, but had WALL•E on the workbench for quite some time awaiting modifications.


The front and rear of the model are not really close to the Pixar design, but it's not a big deal to me.


I wanted a little better detail on the models, so I added some eyes and upgraded the arms.


Then I carved out some rudimentary hands from plastic sprue and glued them to the arms, but had to widen them with plastic strip because I went overboard with my file.

I glued some plastic scraps littering the workbench into a rough square as a load of waste for my second robot to carry.


Some plastic strip that I marked with a Sharpie was added to the arms, and an unmarked strip was added to the rear.


The figure on the left fell on the floor, and the head ended up tilted, but it actually looks pretty good that way.



Not as good as the 1:1 version created by Mike McMaster, but close enough for me.




1 comment:

Web Design & Development said...

I am very thankful to you as your article has given me lots of ideas.This article is awesome! You did a really good job.Thank for sharing. Keep up the good work.

about blockchain technology